Epson Home Cinema 8350 Projector Calibration and Settings

We calibrate each home theater that is reviewed. The Epson Home Cinema 8350, of course, is no exception. Working with a pre-production projector that is 2nd generation (based on the discontinued 8100 UB), rather than an all new unit, this Home Cinema 8350 behaved admirably. No way really to tell it wasn't full production from normal operation and viewing. For that same reason, unlike a first of a series projectors, this is a stable platform, and issues like color table changes should be well behind us.

Ours is a pretty standard calibration, there's always more done to be done by the certified "hi-end" calibrators. Our calibrations, including the Epson Home Cinema 8350, are normally limited to a grayscale calibration, along with brightness, contrast, color saturation, etc. Only in very special circumstances will we calibrate the individual colors, in which case we discuss why.

10/5/10 - Art Feierman

Let's take a look at the numbers:

Epson Home Cinema 8350 Color Temperature

Before we provide our settings, let's see what we started out with: Pre calibration, these are the color temperatures over the grayscale range:

Color Temp over IRE Range (Pre calibration):

Cinema:

30 IRE – 6495
50 IRE – 6539
80 IRE – 6492
100 IRE – 6517 

That's as good as many projectors measure after calibration. Impressive!

^ Back to Top

Epson Home Cinema 8350 Basic Settings

In addition to calibrating Red Green and Blue for a correct grayscale balance (6500K), there are a number of other settings that come into play. Typically Contrast and Brightness (white balance and black balance), need to be done first. Color saturation and gamma also need adjustment.

Below are the settings Mike came up with, as he started the calibration with these controls. (default values are in parenthesis):

Cinema
Dynamic
Living Room
Natural
Contrast = (0) 0 0 -1 0
Brightness= (0) 1 1 2 1
Color Saturation= 0 -10 -5 0
Tint= (0 for all) 0 0 0 0
Color Temp (default)= 6500 6500 9300 6500


Epson Home Cinema 8350 Post Calibration Grayscale: Cinema Gamma, Color Temp based on Medium, and Brilliant Color on:

Calibrated color temps, 20 – 100 IRE: The first set was from our calibration of the engineering sample. The one below it, from the full production Home Cinema 8350. In other words, the second set is pretty much what you can expect. You will notice it is a tighter set of numbers than the original sample, and that's why I'm showing both:

Home Cinema 8350 Projector Grayscale, Gamma Measurements, Post Calibration:

Calibrated color temps, 20 – 100 IRE:

User 1 (Where our calibrated Cinema mode is stored)                     

20 IRE =                         6561                       
30 IRE =                         6521                       
40 IRE =                         6484                       
50 IRE =                         6564                       
60 IRE =                         6520                       
70 IRE =                         6509                       
80 IRE =                         6511                       
90 IRE =                         6521                       
100 IRE =                       6519                       

Average gamma =             2.12                       

NOTE: Mike reports that while the average gamma is a little low, it’s consistently around 2.2 in the lower IRE ranges, which is where it needs to be.  Only at 80 and 90 IRE does in drop below 2.0.

The Epson gamma controls are very flexible, with a number of presets and a gamma "equalizer" (think like a 10 band (octave) audio equalizer). You should be able to raise the gamma just in the 80 and 90 IRE ranges, with the controls.

 

^ Back to Top

RGB Settings

 To get the color temp settings above, the following adjustments were made to Gain and offset. Also listed are the Saturation Tint and Gamma settings. Essentially Mike is saying that you need to set the gamma to 2.4 to get close to a real 2.2.

Calibration settings:                                                                                                                       

Cinema (on User 1)
Quick Cal of Dynamic (User 2)
Offset
R = -5
R= -30
G = 0
G= 0
B = -7
B= 0
Gain
R = -1
R= -10
G = -1
G= -20
B = 0
B= 0
Color Saturation:
-7
0
Tint:
0
0
Gamma:
2.4
2.4
Lumens at 100 IRE:
467
1240

Brightest Mode:

NOTE: Dynamic mode is high in green, low in red at 100 IRE, but high in red as you move down the IRE range, hence the Red cutbacks in the QuickCal.  Overall, the end result looked very good for a brighter mode. Sports looked awesome. Lots of wow factor!


^ Back to Top

NEXT: Recommended projector screens for the Epson Home Cinema 8350 Projector